37’ Melges IC 37 2019 | Midnight Blue
Newport, RI, US
$250,000
“Midnight Blue” is a pristine example of the IC37. She has always been professionally maintained to the highest level. Her pedigree shows with podium finishes at the US Nationals, Winter Series and New York Yacht Club Regattas. Midnight Blue is fully equipped to race at the highest level, she has a US road trailer and all appropriate equipment to step in and win.
Recent Upgrades
Captain maintained from new. This top level boat has had no expense spared to keep her in as-new condition.
Class permitted instrumentation including GPS/ Chart Plotter down below.
Velocitek Pro Start
Custom SeaDek non-skid in cockpit.
Transducer installation
Windex
Small sheet bags w/handle holder for runner winches
Large sheet bags for primaries
Handle holders for mainsheet winches
Handle holders for primary winches
Various covers for cockpit, spars and equipment
2x Dock Boxes on road trailer
High US Road Trailer with Mast supports
Dimensions
PRINCIPLE DIMENSIONS
LOA 37.06 ft 11.30 m
LWL 34.78 ft 10.60 m
BEAM 11.97 ft 3.65 m
DRAFT 8.20 ft 2.50 m
BALLAST 3,373 lb 1,530 kg
DISPLACEMENT 7,793 lb 3,535 kg
DISP/LEN RATIO 83
SAIL DIMENSIONS
JIB 376.74 ft² 35 m²
MAINSAIL 522.05 ft² 48.5 m²
SPINNAKER 1,657.64 ft² 154 m²
SAIL AREA UPWIND 924.6 ft² 85.9 m²
SAIL AREA DOWN (EST) 2093.6 ft² 194.5 m²
SA / WEIGHT UPWIND 36
SA / WEIGHT DOWNWIND 76
I 50.68 ft 15.45 m
J 14.39 ft 4.39 m
P 48.51 ft 14.79 m
E 16.40 ft 5.00 m
STL 22.27 ft 6.79 m
IRC RATING EST: 1.175
Additional Information
STRUCTURE
Hull, Deck, Interior Grid / Gelcoat Surface Multiaxial E-glass and uni-directional carbon fiber Foam core with vacuum wet-preg epoxy resin Secondary bonds hi-strength structural adhesive
KEEL AND RUDDER Carbon keel fin with lead bulb Race faired to class templates – standard Carbon rudder stock w/ blade faired to templates Jeffa self-aligning rudder bearings top and bottom Carbon tiller with an adjustable hiking stick – optional Single point lift padeyes
DECK GEAR BY HARKEN Winches: Primary 2 x H 46.2PTP Mainsheet 2 x H 46.2 STP Pit 1 x H 40.2 STP Backstay 2 x H 46.2 STP Handles 4 x H B10HOT S/G 2 x H B8HOT S/G Traveler track 6:1 cross-haul lead to trimmer Transverse jib tracks: pin stop w / up/down purchase 3 Rope clutches Spinlock XTS0610/1c (main, jib halyard, tack) Aluminum jib sheet fairleads Black stainless steel stanchions and & pulpits Life lines s/s 1 x 19 wire Foredeck hatch Lewmar #65 Trapezoidal
DECK HARDWARE Stainless Steel chainplates 1.25 inch molded foredeck toe rail Recessed plexiglass sliding hatch Ritchie Venture SR-2 compass – in cockpit face
MECHANICAL Yanmar 3YM20CE21 hp Diesel with SD 25 Saildrive Gori 2- blade folding race prop Molded 15-gallon fuel tank w/ deck fill Primary fuel/water filter Spinlock single lever throttle/clutch control
ELECTRICAL 12 VDC system 125-amp alternator with voltage charge balancer 2 X 12 VDC Group 27 batteries 1 X Dual main battery switch 1 X 30-amp main circuit breaker 1 X Blue Seas 4376 switch panel 6 circuit breakers L.E.D. Navigation lights Compass light switched on with Navigation lights 1 X 12 VDC L.E.D. overhead light 5 X L.E.D. AA battery interior lights 2 X 12 VDC / USB charger outlets near switch panel
PLUMBING 1 X Manual diaphragm bilge pump – below deck 1 X Electric bilge pump with extended pick up Raske manual head with integral holding tank Waste deck pump out ¾” Marelon flush mount seacock seawater intake
MAST, BOOM STANDING & RUNNING RIGGING
MAST Southern Spars carbon w/ regatta splice 2 sets carbon swept spreaders Integral mast jack cylinder & hydraulic pump Aluminum mainsail track for slides: full battens & slides 2:1 Main halyard exits below to Spinlock clutch on mast Provision for 2 jib halyards – 1 halyard standard Provision for 2 spinnaker halyards – 1 halyard standard
BOOM Southern Spars aluminum 16:1 outhaul lead to forward end of boom Provision for single reef w/ Clutch in boom (second reef optional)
SPRIT Retractable carbon sprit 2:1 In /Out purchase lead to H-280 & H-150 Cams Single tack-line lead to Spinlock XTS 0610/1C Clutch
STANDING RIGGING S/S rod headstay & shrouds 2 X Dyneema topmast backstays 3:1 to winches
RUNNING RIGGING 1 x Main halyard, 2:1 lead to Spinlock rope clutch below deck 1 x Jib halyard standard (2cnd option) w/ soft shackle 1 x Spinnaker halyard standard (2cnd option) w/ soft shackle 1 x Mainsheet w / provision for continuous lead 2 x Jib sheets with soft shackles 2 x Spinnaker sheets w / soft shackles 1 x Spinnaker tack-line w / soft shackle 1 x Spinnaker retrieving line 2 x Traveler cross-haul 6:1 lead forward to main trimmer 2 x Jib pin stop cars 2 x Jib lead up / down 1 x Cunningham 6:1 lead to pit 1 x Quick Vang purchase lead aft to centerline of pit 1 x Outhaul, 16:1 lead to forward end of boom 1 x Jib Hobble Lead Aft 1 x Spinnaker Takedown System
INTERIOR & FIT OUT Structural carbon reinforced grid Gelcoat structural bulkheads 2 x Storage / seat modules amidships Engine box with gas spring steps Interior hull surfaces epoxy satin clear coat Under deck surfaces epoxy satin clear coat Textured composite covering walk surfaces amidships Flush fasteners – companionway to forward hatch
ONE DESIGN:
One Design corrector weight installed
Complete One Design measurement
One Design certificate issued